Haier Dryer Error Codes (What They Mean + Fixes)

by

If your Haier dryer is displaying an error code, it means the appliance has detected a condition that may interrupt drying or affect performance. This guide explains the most common Haier dryer error codes, what they usually mean, and safe checks you can try before calling service.

Common Haier Dryer Error Codes

E1 — Airflow or Ventilation Error

What it usually means

  • The dryer is not detecting proper airflow.

Try this

  1. Clean the lint filter thoroughly.
  2. Check the exhaust vent for blockages or kinks.
  3. Restart the dryer.

Call service if

  • The error returns after cleaning.

E2 — Heating Error

What it usually means

  • The dryer is not heating to the required temperature.

Try this

  1. Clean lint filters and airflow paths.
  2. Restart and run a normal drying cycle.

Call service if

  • Clothes remain cold and damp.

E3 — Overheating Detected

What it usually means

  • The dryer has detected excessive internal temperature.

Try this

  1. Turn the dryer off and allow it to cool.
  2. Clean all filters before restarting.

Call service if

  • The error returns during the next cycle.

E4 — Door Lock Error

What it usually means

  • The door is not detected as closed or locked.

Try this

  1. Close the door firmly.
  2. Remove laundry caught in the door seal.

Call service if

  • The dryer will not start.

E5 — Temperature Sensor Error

What it usually means

  • The temperature sensor is reporting abnormal readings.

Try this

  1. Turn power off for 5 minutes.
  2. Restart and test a short cycle.

Call service if

  • The error persists.

E6 — Moisture Sensor Error

What it usually means

  • The dryer cannot correctly detect moisture levels.

Try this

  1. Clean moisture sensor bars inside the drum.
  2. Restart the dryer.

Call service if

  • The dryer over-dries or stops too early.

E7 — Motor Error

What it usually means

  • A problem has been detected with the drum motor.

Try this

  1. Reduce load size.
  2. Restart after turning power off.

Call service if

  • The drum does not rotate.

E8 — Motor Overheating

What it usually means

  • The motor has overheated due to airflow restriction or overload.

Try this

  1. Allow the dryer to cool completely.
  2. Clean filters and vents.
  3. Restart with a smaller load.

Call service if

  • The error returns quickly.

E9 — Control Board Error

What it usually means

  • An internal electronic control fault has been detected.

Try this

  1. Turn off power for 5 minutes.
  2. Restart the dryer.

Call service if

  • The dryer will not start.

EF — Airflow Restricted

What it usually means

  • The dryer is detecting restricted airflow.

Try this

  1. Clean lint filter and exhaust vent.
  2. Ensure the vent hose is not crushed.

Call service if

  • Drying times remain very long.

PF — Power Failure

What it usually means

  • The dryer experienced a power interruption.

Try this

  1. Press Start to resume the cycle.
  2. Restart the dryer if needed.

Call service if

  • The error appears without a power outage.

How to Clear a Haier Dryer Error Code

  1. Turn the dryer off.
  2. Switch off power at the wall for 5 minutes.
  3. Restore power and start a short test cycle.

If the error returns immediately, it usually indicates an active fault.

When to Call Service

  • Heating errors that persist after cleaning vents
  • Motor or drum faults
  • Repeated overheating or airflow warnings
  • Control board errors

FAQ

Can blocked vents cause Haier dryer error codes?

Yes. Restricted airflow is one of the most common causes of dryer errors.

Do Haier dryer error codes vary by model?

Yes. Codes may vary slightly by model and region, but the meanings above apply to most Haier dryers.

Is it safe to keep resetting the dryer?

Occasional resets are fine, but repeated resets without fixing the cause are not recommended.