Electrolux Dishwasher Error Codes (What They Mean + Fixes)

by

If your Electrolux dishwasher is showing an error code, it means the appliance has detected a condition that may stop the cycle or affect cleaning performance. This guide covers the most common Electrolux dishwasher error codes, what they usually mean, and safe checks you can try before calling service.

Common Electrolux Dishwasher Error Codes

CLOSE — Door Not Latched

What it usually means

  • The dishwasher door is not fully closed or the latch is not engaging.

Try this

  1. Close the door firmly until it clicks.
  2. Make sure racks are pushed fully in and not blocking the door.
  3. Restart the cycle.

Call service if

  • The message returns even when the door is firmly closed.

i10 / i11 — Water Inlet Problem

What it usually means

  • The dishwasher is not filling with water or not filling fast enough.

Try this

  1. Ensure the water tap is fully open.
  2. Check the inlet hose for kinks.
  3. Clean the inlet filter if accessible.
  4. Power off for 5 minutes and restart.

Call service if

  • No water enters the dishwasher.

i20 — Drain Problem

What it usually means

  • The dishwasher cannot drain water within the expected time.

Try this

  1. Remove and clean the filters thoroughly.
  2. Check the drain hose for kinks or blockages.
  3. Ensure the sink connection is not restricted.

Call service if

  • Water remains in the base after cleaning.

i30 — Leak Detected

What it usually means

  • Water has collected in the base and leak protection has activated.

Try this

  1. Turn the dishwasher off at the power.
  2. Check for visible water under or around the unit.
  3. Allow it to dry before restarting once.

Call service if

  • The error returns or leaking is visible.

i40 / i43 / i44 — Water Level or Pressure Sensor Error

What it usually means

  • The dishwasher is having difficulty detecting the correct water level.

Try this

  1. Clean filters and ensure they are seated correctly.
  2. Avoid using excess detergent.
  3. Restart the dishwasher.

Call service if

  • The error repeats across multiple cycles.

i50 — Wash Motor or Circulation Pump Error

What it usually means

  • A fault has been detected with the circulation motor.

Try this

  1. Power off for 5 minutes.
  2. Ensure spray arms rotate freely.
  3. Restart and try a short cycle.

Call service if

  • The dishwasher stops mid-cycle or makes unusual noises.

i60 / i61 / i69 / i6C — Heating Error

What it usually means

  • The dishwasher is not heating water to the required temperature.

Try this

  1. Restart and run a normal cycle.
  2. Clean filters to ensure proper water flow.

Call service if

  • Dishes remain cold after multiple cycles.

i70 — Temperature Sensor Fault

What it usually means

  • The temperature sensor is sending abnormal readings.

Try this

  1. Power off for 5 minutes.
  2. Restart and test with a short cycle.

Call service if

  • The error continues.

i80 — Configuration or Control Error

What it usually means

  • An internal configuration or control issue has been detected.

Try this

  1. Turn power off for 5 minutes.
  2. Restart the dishwasher.

Call service if

  • The code returns after restart.

i90 — Control System Error

What it usually means

  • A general control fault is preventing normal operation.

Try this

  1. Restart after turning power off.

Call service if

  • The dishwasher will not start.

iF0 / iFo / iF1 — Abnormal Water Level

What it usually means

  • The dishwasher has detected an incorrect water level condition.

Try this

  1. Clean filters and check drainage.
  2. Restart the dishwasher.

Call service if

  • The error repeats.

iC0 — Communication Error

What it usually means

  • Electronic components are not communicating correctly.

Try this

  1. Turn power off for 5 minutes.
  2. Restart the dishwasher.

Call service if

  • The error prevents the dishwasher from starting.

How to Clear an Electrolux Dishwasher Error Code

  1. Turn the dishwasher off.
  2. Switch off power at the wall for 5 minutes.
  3. Restore power and start a short cycle.

If the error returns immediately, it usually indicates an active fault.

When to Call Service

  • Leak-related errors that return after drying
  • Repeated drain or fill errors
  • Heating or motor faults that persist
  • Control or communication errors

FAQ

Can detergent cause Electrolux dishwasher error codes?

Yes. Excess detergent can create foam that interferes with drainage and sensors.

Do Electrolux error codes vary by model?

Yes. Codes can vary slightly by model and region, but the meanings above apply to most Electrolux dishwashers.

Is it safe to keep resetting the dishwasher?

Occasional resets are fine, but repeated resets without fixing the cause are not recommended.